MODELS MZ 15 TO MZ 70

Working time: From 8:00 a.m. to 10:00 p.m

Centimeter Equipment Trading Company Limited

Hotline: 0907030784

Deep groove ball bearing

Home|Product|Deep groove ball bearing

Deep groove ball bearing

MODELS MZ 15 TO MZ 70

Product information

INTRODUCTION

For General Applications							Features:
							1. Prelubricated with special grease
							2. No lubrication maintenance required.
							3. Easy installation and handling

Dimensions and Capacities

Model	Torque Capacity (N·m)	Torque Drag (N·m)	Max. Overrunning (r/min)		Max. indexing (cycle/min)	Bore Size		A	B	C	PCD D	E (M6)	F	G	H-M No.×of Tapped Holes Size× Pitch	S	Weight (kg)
			Inner Race	Outer Race		Dia(H7)	Keyway
MZ15	186	0.20	2,200	900	150	15	5*2.3	62	68	60	58	47	25	5.5	6M5P0.8	10	1.4
MZ17	215	0.20	2,000	800	150	17	5*2.3	66	75	64	64	52	28	6.3	6M5P0.8	10	1.8
MZ20	323	0.29	1,900	700	150	20	6*2.8	67	80	65	68	55	30	7.6	6M6P1.0	12	2.0
MZ30-22	735	0.39	1,800	500	150	22	6*2.8	82	100	80	88	75	45	8.9	6M8P1.25	16	3.7
MZ30-25						25	8*3.3
MZ30						30	10*3.3
MZ35	1,080	0.49	1,700	300	150	35	10*3.3	87	110	85	95	80	50	8.7	6M8P1.25	16	4.8
MZ45-40	1,620	0.69	1,700	300	150	40	12*3.3	92	125	90	110	95	60	8.4	8M8P1.25	16	6.2
MZ45						45	14 *3.8
MZ60-50	2,110	0.98	1,600	250	150	50	14*3.8	102	155	100	140	125	80	9.1	8M8P1.25	16	10.2
MZ60-55						55	16*4.3
MZ60						60	18*4.4
MZ70-65	3,040	1.27	1,300	250	150	65	18*4.4	105	175	103	162	145	95	8.6	8M8P1.25	16	13.2
MZ70						70	20*4.9

Installation and Usage
1. MZ Series Cam Clutch is
Shielded by shield bearings on
both ends, packed with a special
grease, and are ready for use. No
additional lubricant is required.
2. For attaching pulleys, gears or
sprockets to the clutches, insert
hubs (with f 7 tolerance of ISO
R773) along the inner surface of
the outer race and screw the
bolts (high tension) into the
tapped holes on the clutch end.
3. Recommended shaft tolerances
are shown in the table on the
lower left.
4. External thrust load should be
supported by other devices, not
by the Cam Clutch.
5. Use only a parallel key to secure
the clutch to the shaft. Do
not use a tapered Key.
6. When mounting the clutch
onto the shaft, apply
pressure to the inner race
but never to the outer
race. See the illustration
on the right.
7. For vertical mounting,
please consult TSUBAKI.
8. Ambient temperature
range is –5° to 40°C.
9. Key to be used should be
in accordance with ISO
R773. (DIN 6885.1)